|
|
|
|
|
|
|
|
|
|
|
|
|
|
Kero World Kerosene Heater Wick Chart, Dimensions: 0.05 x 8.5 x 11 in
|
General Filters Oil Filter Cartridge, 10 gph, Filter Rating: 10, Filter Media Type: Wool Felt, Suitable for: 77B, 1A-25B, 1A-25A Fuel Oil Filters
|
General Filters Oil Filter Cartridge, Filter Media Type: Microfiber, Suitable for: 77B, 1A-25B, 1A-25A Fuel Oil Filters
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
10-micron wool felt. Center core bonded to prevent media migration.
|
Plumb Pak Coin Air Valve, Metal, Satin Nickel, Dimensions: 2.94 in L x 2 in W x 2.06 in H
|
Necessary for transfer of fuel from storage tank to heater. Easy to operate utilizing a large ball type siphon. Compatible with all types of kerosene heaters.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Male pipe thread x left hand male thread.
|
Male pipe thread x left hand male thread.
|
Male pipe thread x left hand male thread.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
10-micron wool felt. Center core bonded to prevent media migration.
|
1/8 x 27 NPT.
|
Igniters are an important component of correct heater operation. By using an igniter you can avoid unnecessary dirt and damage caused by match lighting.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Igniters are an important component of correct heater operation. By using an igniter you can avoid unnecessary dirt and damage caused by match lighting.
|
Produce a spray that distributes droplets fairly uniformly throughout the complete pattern. The spray pattern becomes progressively more hollow at higher flow rates. Provides smooth ignition and efficient combustion, particularly in larger burners.
|
Replacement part for most Mr. Heater tank top models. Proir to 2011.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1/4 in male pipe threat. Restricted flow, soft nose P.O.L. Most commonly used to connect 1/4 in female pipe thread to 7/8 in female P.O.L.
|
"Soft nose P.O.L. Most commonly used to connect 9/16"" female left hand thread to 7/8"" female P.O.L."
|
"1/8"" angle MIP. Maximum operating pressure 5 PSI. Maximum pressure 10 PSI."
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
7/8 in female P.O.L. x male plug. For use with Mr. Heater's Gas Mate ll Quick Connect Coupling kit F276330. Use L.P gas fill plug for filling the tank with the Gas Mate ll in place. CSA certified. UL approved.
|
60 psi non-shock hot water. 15 psi WSP. Hot water or low pressure systems.
|
1/4 in male pipe thread x 1 in -20 female throwaway cylinder thread.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Neither truly a hollow or solid nozzle. The nozzles frequently can be used in place of either solid or hollow cone nozzles between 0.4 and 8 GPH, regardless of the burner's air pattern. The lower flow rates tend to be more hollow. Higher flow rates tend to be more solid.
|
End fitting for Type 1, QCC-1 gas grill systems. For appliances with 80,000 Btu or less. Threaded shut-off, excess flow safety.
|
Mainly used on burners with a hollow cone air pattern and for throughputs up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Produce a spray that distributes droplets fairly uniformly throughout the complete pattern. The spray pattern becomes progressively more hollow at higher flow rates. Provides smooth ignition and efficient combustion, particularly in larger burners.
|
Mainly used on burners with a hollow cone air pattern and for throughputs up to 2 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion.
|
Produce a spray that distributes droplets fairly uniformly throughout the complete pattern. The spray pattern becomes progressively more hollow at higher flow rates. Provides smooth ignition and efficient combustion, particularly in larger burners.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Mainly used on burners with a hollow cone air pattern and for throughputs up to 2 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion.
|
Produce a spray that distributes droplets fairly uniformly throughout the complete pattern. The spray pattern becomes progressively more hollow at higher flow rates. Provides smooth ignition and efficient combustion, particularly in larger burners.
|
Mainly used on burners with a hollow cone air pattern and for throughputs up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion.
|
|
|
